Gardner ATTS bite alarm range - inc alarms, receivers and accessories

The original ATT ‘silent’ alarms 

set a new benchmark in quality and reliability thanks to their 100% water tight design, excellent build quality and high quality electronics.

Each ATTs head has a latching LED on the front and all audible indication comes from the compatible V2 ATTx and Deluxe wireless receivers. Each ATTs head is tuned into an individual channel on the receiver that lights up, beeps and/or vibrates as set up.

The original ATTs silent head features:

• Soft touch, non-reflective, rubberised finish.

• Built-In transmission that is compatible with the V2 ATTx Receiver and Deluxe Receiver (the alarms must be programmed into a compatible receiver, which provides all the audible and vibratory indication).

• No buttons or knobs for increased reliability. Instead the ATTs heads use a “Intelligent” Protective Hard Case as Standard that acts as the ON/OFF switch for your ATTs, disabling the battery when fitted. Removing the hard case to turn the ATTsi ON.

• All ATTs heads are 100% Watertight! The absence of buttons, jack-plug sockets and speakers reduces the risk of water ingress and electronics damage.

• The rods sit in high parallel ‘ears’ that prevent lateral rod movement and reduce the risk of a rod being pulled off the alarm on vicious takes.

• The ATTs introduces a bite detection system that has ‘anti-rock’ firmware that stops the alarms from giving repetitive false beeps like many other roller wheel alarms do.

• The ATTs alarm comes with a high standard of digital circuitry for total reliability and performance.

• The integtral Low Battery Warning System signals the ATTx receiver which will beep to warn the user of a low battery state on any ATTs head (a series of beeps that register against that heads channel).

• A Betalight Slot on each ear for the dedicated 6mm x 2mm ATTs Tritium Max Betalights (these are sold separately).

• Brass 3/8 BSGF bankstick thread and locking nut will not corrode.

• Ultra-compact and lightweight.

• Supplied already fitted with a Free Test Battery as Standard.

• Height = 64mm, Width = 34mm, Depth = 21mm.

• Full 1 Year ATT Warranty.

• Sensitivity can easily be adjusted by fitting alternative roller wheels. These are available in a wide range of colours and in 2, 4 or 6 magnet roller wheels:

• The 2 magnet wheel the receiver beeps once per 1cm of line movement.

• The 4 magnet wheel the receiver beeps once per 0.5cm of line movement.

• The 6 magnet wheel is ultra-sensitive and beeps once per 0.33cm of line movement.

The Version 2 ATTx Receiver is compatible with V2ATTx Transmitters and all ATTs heads.

Key features of the V2 Receiver include:

• Soft Touch, non-reflective, rubberised finish.

• 5 independent channels.

• Adjustable tone control.

• Volume control.

• Vibrate Mode on/off.

• Excellent range (100m+ in ideal conditions).

• The V2 Receiver is sold with multi-coloured LEDs as standard. These LEDS are set in the following order: Red, Green, White, Orange and Blue.

• The V2 Receiver features a 30 second latching LED showing which alarm has bleeped/triggered.

• Single colour LED Receivers are also available. These include: all blue, red, purple, green, yellow and orange.

• The V2 ATTx receiver only requires a single AA battery (battery not included).

• This single battery will last up to 6 months of regular angling.

Snag Backs Kits

feature the new snag back ears, Neoprene case (with integral magnet to switch the head off) and all the accessories needed to swap the backs over.

The snag backs feature higher parallel ears to help keep the rod safely in place when fishing locked up in thick weed or too snags. These replacement backs fit both the original ATTs and the ATTsiw alarm heads and they negate the need for separate snag ears, offering greater security from the rod being dragged out of the buzzer.

• Feature higher parallel ears – the height of the ears has been increased from 18mm to 28mm.

• Also feature two recesses for the glue fit of a pair of 6 x 2mm Gardner Tritium Max betalights.

• Simply unscrew the original back plates from your alarms and replace them with the Snag Back (replacing the gasket for a perfect seal).

• Snag Back Kit includes: 1 x Snag Back, 1 x Neoprene case (with integral magnet to turn off head), 4 x screws and 1 x gasket seal.